max

Thursday

Dual Zone Passenger's Side HVAC Blend Door Actuator Removal for Dodge RAM Truck?

The complete details for passenger side dual zone blend door actuator removal.

The procedure with step by step directions and diagram.

The details are as follows:---


Dual Zone Passenger's Side



  1. Disconnect and isolate the negative battery cable.
  2. Remove the instrument panel from the vehicle, as follows:
    1. Remove the left A-pillar trim.
    2. Remove the instrument panel top cover.
    3. Disconnect the headliner wire harness connector located at the A-pillar.
    4. Using a trim stick C-4755 or equivalent, from the notch on the bottom, remove the left instrument panel side cover.
    5. Remove the left cowl trim panel.
    6. Remove the steering column.
    7. Remove the two bolts that secure the steering column support bracket to the instrument panel.
    8. Remove the park brake release handle actuator rod.
    9. Disconnect the instrument panel wire harness connector located above the brake pedal from the bulkhead wire harness connector.
    10. Remove the instrument panel drivers side bezel.
    11. Remove the three bolts that secure the left side of the instrument panel to the dash panel.
    12. Remove the floor console, if equipped.
    13. Remove the air bag control module cover, if equipped.
    14. Disconnect the air bag control module electrical connector.
    15. Remove the two bolts that secure the instrument panel to the center of the floor panel.
    16. Remove the right cowl trim cover.
    17. Disconnect the two instrument panel wire harness connectors from the two body wire harness connectors located on the right side of the cowl panel.
    18. Disconnect the antenna coaxial cable connector from the radio coaxial cable connector located on the right side of the cowl panel.
    19. Remove the one bolt that secures the instrument panel to the HVAC housing below the glove box opening.
    20. Using a trim stick C-4755 or equivalent, from the notch on the bottom, remove the right instrument panel side cover from the instrument panel.
    21. Remove the right A-pillar trim.
    22. Remove the three bolts that secure the right side instrument panel bracket to the dash panel.
    23. Remove the four screws that secure the instrument panel to the top of the cowl panel.
    24. Remove the two bolts that secure the instrument panel to the top of the cowl panel.
    25. With the help of an assistant, lift the instrument panel up and off of the cowl panel and remove the instrument panel from the vehicle.
    26. If required, remove the four plastic screws inserts from the top of the cowl panel.
  3. Remove the blend door lever (1) from the blend door actuator output shaft (2) and the blend door linkage (3). 

    image
    Fig. Remove the blend door lever (1) from the blend door actuator output shaft (2) and the blend door linkage (3)
  4. Remove the two screws (1) that secure the blend door actuator and bracket assembly (2) to the top of the HVAC housing (3).
  5. Remove the blend door actuator and bracket assembly from the HVAC housing and disconnect the HVAC wire harness connector (4) from the actuator.
  6. Remove the blend door actuator and bracket assembly from the vehicle. 
    image

    Fig. Remove the two screws (1) that secure the blend door actuator and bracket assembly (2) to the top of the HVAC housing (3). Remove the blend door actuator and bracket assembly from the HVAC housing and disconnect the HVAC wire harness connector (4) from the actuator.
To install:
  1. Install the blend door actuator and bracket assembly onto the top of the HVAC housing.
  2. Install the screws that secure the blend door actuator and bracket assembly to the HVAC housing. Tighten the screws to 20 inch lbs. (2.2 Nm).
  3. Connect the HVAC wire harness connector to the blend door actuator.
    NOTE
    Align the guide pin on the blend door lever with the guides on the blend door linkage during installation of the blend door lever.
  4. Install the blend door lever onto the blend door actuator output shaft and the blend door linkage.
  5. Install the instrument panel, as follows:
    1. If removed, install the four plastic screw inserts into the top of the cowl panel.
    2. With the help of an assistant, position the instrument panel into the vehicle and install the right side guide pin and the left side guide hook to the sides of the cowl panel.
    3. Install the two bolts that secure the instrument panel to the top of the cowl panel. Tighten the bolts to 9 ft. lbs. (12 Nm).
    4. Install the four screws that secure the instrument panel to the top of the cowl panel. Tighten the screws to 20 inch lbs. (2.2 Nm).
    5. Install the three bolts that secure the right side instrument panel bracket to the cowl panel. Tighten the bolts to 9 ft. lbs. (12 Nm).
    6. Install the right A-pillar trim.
    7. Install the right instrument panel side cover.
    8. Install the one bolt that secures the instrument panel to the HVAC housing below the glove box opening. Tighten the bolt securely.
    9. Connect the radio coaxial cable connector to the antenna coaxial cable connector located on the right side of the cowl panel.
    10. Connect the two instrument panel wire harness connectors to the two body wire harness connectors located on the right side of the cowl panel.
    11. Install the right cowl trim panel.
    12. Install the two bolts that secure the instrument panel to the center of the floor panel. Tighten the bolts to 9 ft. lbs. (12 Nm).
    13. Connect the air bag control module electrical connector.
    14. Install the air bag control module cover, if equipped.
    15. Install the floor console, if equipped.
    16. Install the three bolts that secure the left side of the instrument panel to the dash panel. Tighten the bolts to 9 ft. lbs. (12 Nm).
    17. Install the instrument panel drivers side bezel.
    18. Install the left cowl trim panel.
    19. Connect the instrument panel wire harness connector located above the brake pedal to the bulkhead wire harness connector.
    20. Install the park brake release handle actuator rod.
    21. Install the two bolts that secure the steering column support bracket to the instrument panel. Tighten the bolts to 10 ft. lbs. (14 Nm).
    22. Install the steering column.
    23. Install the left cowl trim cover.
    24. Install the left instrument panel side cover.
    25. Connect the headliner wire harness connector located at the A-pillar.
    26. Install the instrument panel top cover.
    27. Install the left A-pillar trim.
  6. Reconnect the negative battery cable.



These details will help.
Thanks.           

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html




No comments:

Post a Comment