max

Tuesday

How To replace Rear Brake Pads on Ford?

The ford Rear Brake pads removal procedure is as follows: ----


REAR Brake Pads
REMOVAL & INSTALLATION Details are mentioned below:---


  1. Remove the brake master cylinder reservoir cap. Siphon and recycle approximately half the fluid from the reservoir.
  2. Raise and support the vehicle safely.
  3. Remove the wheels.
    NOTE
    Do not press against the brake pad spring clip.
  4. Position the C-clamp frame on the inboard side of the rear disc brake caliper housing. Position the clamp screw on the outboard brake pad backing plate.
  5. Tighten the C-clamp sufficiently to press the rear disc brake caliper piston to the bottom of the caliper bore.
  6. Remove the caliper bolts.
    NOTE
    Do not allow the caliper to hang by the rear brake hose.
  7. Work the caliper off the rear disc brake rotor and brake adapter.
  8. Remove the slippers from the anchor plate abutments by gently prying them of the rails. Discard the old slippers.
  9. Remove the brake pads.
To install:

NOTE
New slippers must be used on the rail abutments for proper operation of the caliper assembly.

  1. Inspect the anchor plate rail abutments for wear or damage. Replace as necessary.
  2. Install new anti-wear slippers on the rail abutments by snapping them into place.
  3. Position the brake pads on the caliper and rotate it down until the locating lugs and retainer spring are fully seated.
  4. Install the rear disc brake caliper on the rotor. Make sure the notches on the upper ends of the brake pad are seated over the upper ledge of the adapter and the brake pad lower tabs are positioned on the lower ledge of the adapter.
  5. Lubricate the caliper bolts with Disc Brake Caliper Slide Grease (D7AZ-19590-A) or equivalent. Install and tighten to 11-14 ft. lbs. (15-20 Nm).
    NOTE
    Failure to tighten the lug nuts to the proper torque in a star pattern may result in damage to the brake rotor.
  6. Install the wheel and tighten the lug nuts to 83-112 ft. lbs. (113-153 Nm).
  7. Lower the vehicle.
  8. Pump the brake pedal to seat the brake pads.
  1. Remove 1 / 2 of the brake fluid from the brake master cylinder reservoir. Properly dispose of the brake fluid.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Using a C-clamp or equivalent, position the clamp frame on the inboard side of the disc brake caliper housing. Place the clamp screw on the outboard disc brake pad and tighten the clamp enough to press the caliper piston into the caliper housing releasing pressure on the disc brake pads. 

    image
    Fig. Rear disc brake components-Windstar
  5. Remove 2 disc brake caliper retaining bolts. Do not remove the disc brake caliper brake hose from the caliper.
  6. Work the disc brake caliper off the brake rotor and disc brake adapter. Move the disc brake caliper aside and secure with wire or equivalent to prevent damage to the brake hose.
  7. Remove the slippers from the anchor plate abutments by gently prying them off the rails and discard the slippers.
  8. Remove the inner and outer disc brake pads.
  9. Inspect the disc brake rotor surfaces for grooves, cracks or glazing. Resurface or replace as required. If resurfacing, observe the minimum thickness specification.
To install:
  1. Retract the disc brake caliper piston fully into the caliper bore using a C-clamp and block of wood or equivalent. This will make room for the new disc brake pads.
  2. Install new anti-wear slippers on the rail abutments by snapping them in place.
  3. Install new inner and outer disc brake pads. Ensure that the disc brake pads are properly positioned and that the lining material is facing the rotor.
  4. Install the disc brake caliper over the brake rotor and place on the brake adapter. Ensure that the notches on the upper ends of the brake pads are seated over the upper ledge of the disc brake adapter and the lower tabs are placed on the lower ledge of the disc brake adapter.
  5. Lubricate 2 disc brake caliper retaining bolts with a suitable grease and install. Tighten the retaining bolts to 11-14 ft. lbs. (15-20 Nm).
  6. Install the wheel and tire assembly. Torque the lug nuts to 85-105 ft. lbs. (115-142 Nm).
  7. Lower the vehicle.
  8. Pump the brake pedal several times to position the brake pads before attempting to move the vehicle.
  9. Check and fill the brake master cylinder reservoir, as required.
  10. Road-test the vehicle and check for proper brake operation.

This details will help.
Thanks.




FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html


No comments:

Post a Comment