max

Wednesday

Toyota 5VZ-FE Engine Camshaft replacing procedure?


Camshaft, Bearings & Lifters
REMOVAL & INSTALLATION procedure for Toyota 4Runner models.
Its also suggested to go through this help section to get complete detail about camshaft ,bearings and lifter removal:----]

How to Replace Toyota 4runner Camshaft, Bearings & Lifters ?

http://howtobyme.blogspot.in/2012/03/how-to-replace-toyota-4runner-camshaft.html


  1. Remove the right exhaust camshaft as follows:
    1. Bring the service bolt hole of the driven sub-gear upward by turning the hexagon head portion of the exhaust camshaft with a wrench.
    2. Align the timing mark (two dot marks) of the camshaft drive and driven gears by turning the camshaft with a wrench.
    3. Secure the exhaust camshaft sub-gear to the driven gear with a service bolt 6mm in diameter by 1.0mm pitch thread, 16-20mm long.
When removing the camshaft, make sure that the torsion spring force of the sub-gear has been eliminated by the above operation.
  1. Uniformly loosen and remove the bearing cap bolts in several passes, in the sequence shown.
  2. Remove the bearing caps and camshaft. Make a note of the bearing cap positions for proper installation.

WARNING
Do NOT pry on or attempt to force the camshaft with a tool or other object.

  1. Remove the right hand intake camshaft as follows:
    1. Uniformly loosen and remove the bearing cap bolts in several passes, in the sequence shown.
    2. Remove the bearing caps, oil seal and camshaft. Make a note of the bearing cap positions for proper installation.
image 

Fig. Loosen the right hand intake camshaft caps as shown-5VZ-FE engine


image
Fig. When aligning the gears, turn the camshaft with the flats provided. Do NOT place a wrench on the lobes-5VZ-FE engine


Click image to see an enlarged view
Fig. The spring force of the sub-gear can be overcome by using a 6mm restraining bolt-5VZ-FE engine


Click image to see an enlarged view
Fig. Left hand exhaust camshaft bearing cap loosening sequence-5VZ-FE engine
  1. Remove the left exhaust camshaft as follows:
    1. Align the timing mark (1 dot mark) of the camshaft drive and driven gears by turning the camshaft with a wrench.
    2. Secure the exhaust camshaft sub-gear to the driven gear with a service bolt 6mm in diameter by 1.0mm pitch thread, 16-20mm long.
When removing the camshaft, make sure that the torsion spring force of the sub-gear has been eliminated by the above operation.
  1. Uniformly loosen and remove the bearing cap bolts in several passes, in the sequence shown.
  2. Remove the bearing caps and camshaft. Make a note of the bearing cap positions for proper installation.

WARNING
Do NOT pry on or attempt to force the camshaft out.

  1. Remove the left hand intake camshaft as follows:
    1. Uniformly loosen and remove the bearing cap bolts in several passes, in the sequence shown.
    2. Remove the bearing caps, oil seal and camshaft. Make a note of the bearing cap positions for proper installation.


Click image to see an enlarged view
Fig. The left hand intake camshaft caps must be loosened as shown-5VZ-FE engine
To install:
  1. Install the right intake camshaft as follows:
    1. Apply engine oil to the thrust portion of the intake camshaft.
    2. Position the intake camshaft at a 90° angle of the timing mark (two dot marks) on the cylinder head.
    3. Install the bearing caps in their proper locations. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts. Install the cap bolts.
    4. Uniformly tighten the cap bolts in the sequence shown to 12 ft. lbs. (16 Nm).


Click image to see an enlarged view
Fig. Tighten the right side intake camshaft caps as shown-5VZ-FE engine
  1. Install the right exhaust camshaft as follows:
    1. Apply engine oil to the thrust portion of the intake camshaft.
    2. Align the timing marks (two dot marks) of the camshaft drive and driven gears.
    3. Roll down the exhaust camshaft onto the bearing journals while engaging the gears with each other. Install the bearing caps in their proper locations.
    4. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts. Install the cap bolts.
    5. Uniformly tighten the cap bolts in the sequence shown to 12 ft. lbs. (16 Nm).
    6. Remove the service bolt from the driven sub-gear. Check that both the intake and exhaust camshafts turn smoothly.
    7. Align the timing marks (two dot mark) of the camshaft drive and driven gears by turning the camshaft with a wrench.


Click image to see an enlarged view
Fig. When installing the exhaust camshaft, make sure the timing marks align-5VZ-FE engine


Click image to see an enlarged view
Fig. Use this sequence to tighten the right hand exhaust camshaft bearing cap bolts-5VZ-FE engine
  1. Install the left intake camshaft as follows:
    1. Apply engine oil to the thrust portion of the intake camshaft.
    2. Position the intake camshaft at a 90° angle of the timing mark (one dot mark) on the cylinder head.
    3. Install the bearing caps in their proper locations. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts. Install the cap bolts.
    4. Uniformly tighten the cap bolts in the sequence shown to 12 ft. lbs. (16 Nm).


Click image to see an enlarged view
Fig. Tightening sequence for the left hand intake camshaft cap bolts-5VZ-FE engine
  1. Install the left exhaust camshaft as follows:
    1. Apply engine oil to the thrust portion of the intake camshaft.
    2. Align the timing marks (1 dot marks) of the camshaft drive and driven gears.
    3. Roll down the exhaust camshaft onto the bearing journals while engaging the gears with each other. Install the bearing caps in their proper locations.
    4. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts. Install the cap bolts.
    5. Uniformly tighten the cap bolts in the sequence shown to 12 ft. lbs. (16 Nm).
    6. Remove the service bolt.


Click image to see an enlarged view
Fig. Tighten the left side exhaust camshaft cap bolts in this sequence-5VZ-FE engine
  1. Check and adjust the valve clearance.
  2. Install the semi-circular plugs.
  3. Install the cylinder head covers. Uniformly tighten the bolts in several passes to 53 inch lbs. (6 Nm).



view this additional HELP DIAGRAM FOR MORE KNOWLEDGE AND EASY WORKING ON THIS TASK:----

Removal & Installation



5VZ-FE Engine
  1. Remove both cylinder head covers.
  2. Remove the semi-circular plugs.


Click image to see an enlarged view
Fig. Remove the cylinder head covers from the engine-5VZ-FE engine


Click image to see an enlarged view
Fig. Align the gears by turning the camshaft with a wrench on the flats provided-not the lobes-5VZ-FE engine


Click image to see an enlarged view
Fig. Removing the bolt from the camshaft pulley


Click image to see an enlarged view
Fig. Carefully detach the camshaft pulley


Click image to see an enlarged view
Fig. Be careful not to lose the dowel pin


Click image to see an enlarged view
Fig. The camshaft pulleys are marked right and left


Click image to see an enlarged view
Fig. Left and right camshaft pulleys-5VZ-FE engine


Click image to see an enlarged view
Fig. Unfasten the camshaft's bearing cap retaining bolts . . .


Click image to see an enlarged view
Fig. . . . then remove the camshaft bearing cap


Click image to see an enlarged view
Fig. Lift the rear bearing cap and pull out the camshaft seal


Click image to see an enlarged view
Fig. Carefully remove the camshaft from the cylinder head


Click image to see an enlarged view
Fig. Use an appropriate size bolt to release the spring force of the sub-gear-5VZ-FE engine


Click image to see an enlarged view
Fig. Right hand exhaust camshaft bearing cap loosening sequence-5VZ-FE engine

These details will help.
Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html



No comments:

Post a Comment