max

Wednesday

How to replace Front wheel bearing?

In this case the customer has Toyota Corolla Old model.

He needs to replace right side front wheel bearing for his Toyota.As per his requirement the details are as follows.

First of all,this requires proper tools.The tools for pressing the bearing.Its called press tool.

See below the diagram:---







You will need to have a bearing puller (slide hammer with jaw attachments), a bearing race driver, and a torque wrench to complete this repair; these are common tools found in any repair shop and many home garages. As an alternative, you can remove the steering knuckle from the vehicle and take it to a machine shop and let them change the bearing and then reinstall it, but you will need to have a wheel alignment performed afterwards because the upper knuckle-to-strut bolts are alignment adjustment bolts.

Here is the procedure if you want to give it a try:

______________________


Raise and support front of vehicle, then remove tire and wheel assembly.
Remove cotter pin and bearing locknut cap.
With brake pedal depressed, remove bearing locknut.
Remove brake caliper from steering knuckle and suspend out of way.
Remove disc rotor, then ensure bearing play in axial direction does not exceed .002 inch.
Remove cotter pin and nut, then, using suitable puller, disconnect tie rod end from steering knuckle.
Scribe alignment marks on strut lower bracket and camber adjusting cam (if equipped).
Remove steering knuckle-to-strut lower bracket attaching nuts and bolts.
Disconnect steering knuckle from lower suspension arm.
Using plastic hammer, tap axle shaft to loosen it while removing steering knuckle and axle hub. On some applications, it may be necessary to use puller to remove hub from axle shaft. Cover driveshaft boot with cloth to prevent damage.
If necessary, remove ball joint from steering knuckle.
Using suitable tool, remove dust deflector (if equipped) and inner oil seal from steering knuckle.
Using suitable pliers, remove axle hub snap ring.
Remove three bolts securing disc brake dust cover to steering knuckle.
Using suitable puller, remove hub from steering knuckle.
Remove inside bearing inner race from bearing.
Using suitable puller, remove outside inner race from axle hub.
Using suitable screwdriver, remove oil seal from steering knuckle.
Place an outside bearing inner race on bearing and, using suitable tool and hammer, drive out bearing. Always replace the bearing as an assembly.
Using suitable tool, press new bearing into steering knuckle.
Rotate and insert the side lip of a new outer oil seal into tool 09608-32010 or equivalent, then, using tool 09710-14012 or equivalent, drive oil seal into steering knuckle.
Apply suitable grease to oil seal lip.
Install disc brake dust cover.
Apply suitable grease to oil seal and bearing, then, using suitable tool, press hub into steering knuckle.
Install hub snap ring in steering knuckle.
Using suitable tool, drive a new oil seal and dust deflector (if equipped) into steering knuckle surface, then apply suitable grease to oil seal lip and axle shaft.
If removed, install ball joint.
Reverse procedure to install, torque two strut-to-steering knuckle attaching nuts and bolts, steering knuckle-to-lower suspension arm attaching bolts, tie rod end attaching nut and bearing locknut to specifications.

This will help.
See below the latest solved car problems.



Front wheel hub assembly Diagram and replacing procedure?

http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html

Front wheel assembly diagram to replace wheel bearing?

http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html



Gas door hinges broken on Toyota?

http://technoanswers.blogspot.in/2012/02/gas-door-hinges-broken-on-toyota.html

Where is the bulb located in glove box?

http://repairhelpcenter.blogspot.com/2012/01/where-is-bulb-located-in-glove-box.html

Additional wiring harness needs to be installed in a brake controller for electric brakes on 2012 Toyota Highlander?

http://repairhelpcenter.blogspot.com/2012/01/additional-wiring-harness-needs-to-be.html

Fail smog test due to gas filter hose?

http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html

Clutch squeaking under hood?

http://repairhelpcenter.blogspot.com/2012/01/clutch-squeaking-under-hood.html

How to remove Rear Adjustable Arm on 2007 Toyota Camry?

http://schematicsdiagram.blogspot.in/2012/02/how-to-remove-rear-adjustable-arm-on.html

Engine stalls when gas is given?

http://technoanswers.blogspot.in/2012/01/engine-stalls-when-gas-is-given.html

4x4 front differential will not engage the axle on ford?

http://technoanswers.blogspot.in/2012/02/4x4-front-differential-will-not-engage.html

1990 mazda 323 stalls and quit running?

http://technoanswers.blogspot.in/2012/02/1990-mazda-323-stalls-and-quit-running.html

Where is Crankshaft position sensor located on Toyota Tundra?

http://schematicsdiagram.blogspot.in/2012/02/where-is-crankshaft-position-sensor.html

Nissan car will not start?

http://technoanswers.blogspot.in/2012/02/nissan-car-will-not-start.html

Delay starting on Toyota Prius?

http://schematicsdiagram.blogspot.in/2012/02/delay-starting-on-toyota-prius.html

Honda car will not start intermittently?

http://technoanswers.blogspot.in/2012/02/honda-car-will-not-start-intermittently.html

Toyota car will not start?

http://technoanswers.blogspot.in/2012/02/toyota-car-will-not-start.html

Cooling fan relays location on 1998 ford mustang?

http://technoanswers.blogspot.in/2012/02/cooling-fan-relays-location-on-1998.html

2009 Chevy impala accelerator pedal sensor?

http://technoanswers.blogspot.in/2012/02/2009-chevy-impala-accelerator-pedal.html


No comments:

Post a Comment