@

max

Tuesday

How to locate the vacuum leak?

You will have to find it.While driving your vehicle has minimal vacuum it creates the most when idling or at a stop. You are having to give it gas to compensate for the car getting to much air. Check all the hoses that attach to the intake and check the intake use carb cleaner it works perfect.

You could be looking for a small hole or a large one. Next to your air filter is a MAF mass air flow meter. It tells the computer how much air is coming into the engine between the MAF and the O2 sensors in the exhaust there is a problem. Your computer is telling you that there is more air getting in somewhere more than what the MAF send signal to it. So this means if a vacuum leak is your problem which it most likely is.Its are sucking/getting more air either around the intake gaskets or around the vacuum lines going to the intake or around the throttle body or the sensors attached to it. Most of all the hoses on your engine are smaller than your thumb are vacuum lines. You need to spray carb cleaner all over the engine and around these hoses to find a leak. The rpms will increase when you hit a leak because the car will suck the carb cleaner in and use it as a fuel and it will rev slightly. There is no common area of failure and there is not a common part that fails. You will have to take it to a dealer to repair or find the problem yourself. I highly recommend you give it a shot before sending it to a technician.

This details will help.
Thanks.

See below latest solved car problems :---

Vacuum Hose Routing Diagram For 1995 Chevrolet Corvette Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html



VACUUM DIAGRAMS For Audi A4?


VACUUM DIAGRAMS For VW Passat?

http://vwrepairhelp.blogspot.com/2011/11/vacuum-diagrams-for-vw-passt.html

Vacuum line diagram For 1996 Chevrolet Lumina?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-line-diagram-for-1996-chevrolet.html

Vacuum Hose Routing Diagram For 1995 Chevrolet Corvette Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html

Vacuum diagram for Isuzu?

http://technoanswers.blogspot.com/2012/01/vacuum-diagram-for-isuzu.html

Traction control message?

http://schematicsdiagram.blogspot.com/2012/01/traction-control-message.html

How to replace Exhaust Manifold in Audi and VW car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-in-audi.html

 

           

How to replace Intake Manifold in Audi and VW car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-in-audi.html

                                

How to replace Radiator on Audi and VW car models?


How to Replace Engine cooling Fan on Audi A4?


Engine won’t rev up past half throttle?

http://technoanswers.blogspot.com/2012/01/engine-wont-rev-up-past-half-throttle.html

2004 ford freestar van idles rough?

Properly inspect if you  find a leak in the Vacuum hose that goes to the pcv valve right at the elbow that plugs intothe intake?Not on the PCV valve side but on the other end. Also on top of that there is a clip that holds a lever in place ,see properly if that lever is ok or completely gone. 

Those are your IMRC Actuator Rod Clips.

When you get a diagnostic trouble code P2195 and P2197,it does not necessarily mean that a sensor is bad or failed. This codes also means that the computer is not getting the signal, e.g. volts, ohms, amps, that it is programmed to expect. 
There are many possible reasons for these,
It could be a failed sensor, but it could also be a bad connection, a short or an open wire, or the information is correct, e.g. a lean condition caused by a vacuum leak which would cause the oxygen sensor to not "switch" from rich to lean and back as often as is expected. The sensor would stay on lean and trigger the code. The same condition can, and often does, trigger more than one code.
This all has to be checked.

Basically in this types of cases,the problem here is most likely a large vacuum leak causing a lean air mixture. Most common (very common) are the crankcase ventilation hoses to crack or collapse causing a vacuum leak. Also, the air intake tubes crack and cause this problem. The clamps on the air intake tubes must be tight and secured properly to seal correctly. There are 2 of the crankcase ventilation tubes one to each valve cover. Inspect them closely looking for any cracks or holes. Make sure they are on as well. There are also a number of other vacuum hoses that can rip/tear causing vacuum leaks. All vacuum hoses are of little expense to repair. Other possibilities are a leaking intake gasket. These are common to fail as well. Intake gaskets can be a significant expense $300 to $400 depending on shop rates. It is unlikely that the oxygen (O2) sensors are causing this problem. The best way to diagnose this problem is using a smoke machine. This is a machine that releases smoke. By hooking up a smoke machine to the air intake, you can easily pinpoint any vacuum leaks.

This will help.

Also check this direct link:----


Check engine light with codes P2195 and P2197?

The check engine light comes on because the computer misinterprets the O2 input. You need to have the PCM software updated.

The details for both the OBD error codes are as follows :----


P2195 - Lack of HO2S-11 Switch, Sensor Indicates Lean

A HEGO sensor indicating lean at the end of a test is trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects switching for a calibrated amount of time.

Electrical:
Short to VPWR in harness or HO2S
Water in harness connector
Open/Shorted HO2S circuit
Corrosion or poor mating terminals and wiring
Damaged HO2S
Damaged PCM
Fuel System:
Excessive fuel pressure
Leaking/contaminated fuel injectors
Leaking fuel pressure regulator
Low fuel pressure or running out of fuel
Vapor recovery system
Induction System:
Air leaks after the MAF
Vacuum Leaks
PCV system
Improperly seated engine oil dipstick
EGR System:
Leaking gasket
Stuck EGR valve
Leaking diaphragm or EVR
Base Engine:
Oil overfill
Cam timing
Cylinder compression
Exhaust leaks before or near the HO2S(s)

____________________________________________________

P2197 - Lack of HO2S-21 Switch, Sensor Indicates Lean

A HEGO sensor indicating lean at the end of a test is trying to correct for an over-rich condition. The test fails when fuel control system no longer detects switching for a calibrated amount of time.

These codes mean you have lean codes on both sides of the engine most likely caused by a vacuum leak. If it is a large leak you will hear a hissing noise while idleing. To find small vacuum leaks while running spray carb cleaner around the intake and all the vacuum lines attached to the intake the full length of the hoses. A vacuum leak can start any where after the MAF to the cylinders.

Once repaired the vehicle will need to be cleared of faults by removing the negative battery cable for 15 minutes.

This details will help.
Thanks.

See below latest OBD related solutions :---

OBD code P0768?

http://repairhelpcenter.blogspot.com/2012/01/obd-code-p0768.html

Evaporative Emissions System codes details?

http://schematicsdiagram.blogspot.com/2011/11/evaporative-emissions-system-codes.html

 

Engine Misfire codes on Chevrolet Malibu?


Misfire on cylinder 4?

ABS trouble codes for all 1994-00 Acura models?

Diagnostic code P0010?

http://schematicsdiagram.blogspot.com/2011/12/diagnostic-code-p0010.html

Diagnostic Code P1396?


Code P0452?


OBD code P0172 on Buick Park Avenue?


DTC Code P0321 on Buick Park Avenue?


Error Code P0471 on 2007 Dodge Ram 3500?


P0304 Error code on Dodge Neon?


OBDII scan is receiving NO BUS CODE?


How to Clear OBD error Codes on Acura Car Models?


Diagnosis and Testing Car Components?

Diagnostic Trouble Codes list for Acura Car Models?

Part 1.

Diagnostic Trouble Codes list for Acura Car Models?

Part 2.

Diagnostic Code 43 and 71 on 1991 Toyota Pickup?


Code P0132 On Acura TL?

P0031 code on Dodge Dakota?

How to get diagnostic Code without OBD Scanner on Pre 1995 Toyota Pickup?

OBD-II Trouble Code P0300?

Getting diagnostic code P0016?

How to Read Codes from Check Engine Light?

Diagnostic Code P0540 continues to return and the MIL light is on?

DTC Trouble Code P0401?

Car misfires and error code P0306 and P0303 is shown?

Diagnostic code P0463 on Ford F250?

http://technoanswers.blogspot.com/2012/01/diagnostic-code-p0463-on-ford-f250.html

Monday

How to bleed power steering pump?

It will work well for Mitsubishi car models :----


Bleeding


See below the details :-----

  1. Raise the vehicle and support safely.
  2. Manually turn the oil pump pulley a few times.
  3. Turn the steering wheel all the way to the left and to the right 5 or 6 times.
  4. Disconnect the ignition high tension cable and, while operating the starter motor intermittently, turn the steering wheel all the way to the left and right 5-6 times for 15-20 seconds. During bleeding, make sure the fluid in the reservoir never falls below the lower position of the filter. If bleeding is attempted with the engine running, the air will be absorbed in the fluid. Bleed only while cranking.
  5. Connect ignition high tension cable, start engine and allow to idle.
  6. Turn the steering wheel left and right until there are no air bubbles in the reservoir. Confirm that the fluid is not milky and the level is up to the specified position on the gauge. Confirm that there is very little change in the fluid level when the steering wheel is turned. If the fluid level changes more than 0.2 in., the air has not been completely bled. Repeat the process.

Front



  1. Raise the vehicle and support safely.
  2. Manually turn the pump pulley a few times.
  3. Turn the steering wheel all the way to the left and to the right 5 or 6 times.
  4. Disconnect the ignition high tension cable and, while operating the starter motor intermittently, turn the steering wheel all the way to the left and right 5-6 times for 15-20 seconds. During bleeding, make sure the fluid in the reservoir never falls below the lower position of the filter. If bleeding is attempted with the engine running, the air will be absorbed in the fluid. Bleed only while cranking.
  5. Connect ignition high tension cable, start engine and allow to idle.
  6. Turn the steering wheel left and right until there are no air bubbles in the reservoir. Confirm that the fluid is not milky and the level is up to the specified position on the gauge. Confirm that there is very little change in the fluid level when the steering wheel is turned. If the fluid level changes more than 0.2 in. (5mm), the air has not been completely bled. Repeat the process.

Rear



  1. Bleed the front steering system.
  2. Start the engine and let it idle.
  3. Loosen the bleeder screw on the left side of the control valve and install special tool MB991230 to the bleeder.
  4. Turn the steering wheel all the way to the left, then immediately turn it halfway back. Confirm that air has discharged with the fluid.
  5. Repeat Step 4 two or three times as required, to remove all air from the rear system. Stop the engine.
  6. Loosen the power cylinder (rear steering gear) bleeder screw about 1 / 8 turn and install the same special tool with the rotation prevention metal fixtures to prevent the bleeder from opening more.
  7. Start the engine and run to 50 mph to circulate the fluid.
  8. Maintain a speed of 20 mph and turn the steering wheel back and forth. Air should be discharged through the tube of the special tool and into the oil reservoir.
  9. Repeat until all air is removed from the power cylinder.

See below latest solved car problems :----

How to remove Intake Manifold Tuning Valve?

http://technoanswers.blogspot.com/2012/01/how-to-remove-intake-manifold-tuning.html

CMFI details for GMC vehicles?

http://technoanswers.blogspot.com/2012/01/cmfi-details-for-gmc-vehicles.html

Mazda MPV cranks but will not start?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-cranks-but-will-not-start.html

MAZDA MPV WILL CRANK BUT NOT TURN OVER TO START?

http://technoanswers.blogspot.com/2012/01/mazda-mpv-will-crank-but-not-turn-over.html

Freightliner fl112 fuse box diagram?

http://technoanswers.blogspot.com/2012/01/freightliner-fl112-fuse-box-diagram.html

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

Car only starts when gas pedal is pressed?

http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html

Hyundai coupe f2 hazard fault?

http://schematicsdiagram.blogspot.com/2012/01/hyundai-coupe-f2-hazard-fault.html

Where is the bulb located in glove box?

http://repairhelpcenter.blogspot.com/2012/01/where-is-bulb-located-in-glove-box.html

Additional wiring harness needs to be installed in a brake controller for electric brakes on 2012 Toyota Highlander?

http://repairhelpcenter.blogspot.com/2012/01/additional-wiring-harness-needs-to-be.html

Fail smog test due to gas filter hose?

http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html

Clutch squeaking under hood?

http://repairhelpcenter.blogspot.com/2012/01/clutch-squeaking-under-hood.html

Replace door stay assemblies on Toyota?

http://repairhelpcenter.blogspot.com/2012/01/replace-door-stay-assemblies-on-toyota.html

Acceleration lag problem?

http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html

How to Replace rear quarter glass on Toyota Tacoma?

http://repairhelpcenter.blogspot.com/2012/01/how-to-replace-rear-quarter-glass-on.html

Overdrive light in the dash blinks?

http://repairhelpcenter.blogspot.com/2012/01/overdrive-light-in-dash-blinks.html

No pulse to injectors?

http://technoanswers.blogspot.com/2012/01/no-pulse-to-injectors.html

How to bypass immobiliser on Rover 200?

http://technoanswers.blogspot.com/2012/01/how-to-bypass-immobiliser-on-rover-200.html

Hood clear coat peeling off?

http://repairhelpcenter.blogspot.com/2012/01/hood-clear-coat-peeling-off.html

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

How to Refit Rear seat on Rover 600?

http://repairhelpcenter.blogspot.com/2012/01/how-to-refit-rear-seat-on-rover-600.html

How to replace the speakers on 2011 Ford Edge?

http://technoanswers.blogspot.com/2012/01/how-to-replace-speakers-on-2011-ford.html

How to Remove Rear seat on Rover 600?

http://repairhelpcenter.blogspot.com/2012/01/there-are-3-10mm-bolts-at-back-of-seats.html

Toyota solara rattling in rear?

http://technoanswers.blogspot.com/2012/01/toyota-solara-rattling-in-rear.html

Parking light stay on constantly?

http://repairhelpcenter.blogspot.com/2012/01/parking-light-stay-on-constantly.html

Engine hard to start after gas refill?

http://repairhelpcenter.blogspot.com/2012/01/engine-hard-to-start-after-gas-refill.html

How to replace wheel bearing on Honda Civic?

http://repairhelpcenter.blogspot.com/2012/01/how-to-replace-wheel-bearing-on-honda.html

Do snow tires go on the back or front?

http://howtobyme.blogspot.com/2012/01/do-snow-tires-go-on-back-or-front.html

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html


how to replace power steering pump on Mitsubishi Diamante?

The procedure is as follows :----

Removal & Installation



image
Fig. Exploded view of the power steering pump-Mirage
  1. Drain the power steering system as follows:
  1. Disconnect the return hose at the reservoir and place into a suitable container.
  2. Disable the ignition system. While cranking the engine, turn the wheels several times, until system has been drained.
  1. Disconnect the battery negative cable.
  2. Remove the pressure switch connector from the side of the pump.
  3. If the alternator is located under the oil pump, cover it with a shop towel to protect it from oil.
  4. Disconnect the pressure line.
  5. Remove the steering pump drive belt and the water pump pulley drive belt.
  6. Remove the water pump pulley.
  7. Remove the bolts that secure the oil pump, then remove the pump from its bracket.
To install:
  1. Install the power steering pump and tighten the mounting bolts to specifications.
  2. Install the water pump pulley and tighten the mounting bolts 14 ft. lbs. (19 Nm).
  3. Install and adjust the drive belts.
  4. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the nut that secures the pressure line to 13 ft. lbs. (18 Nm).
  5. Connect the return line.
  6. Attach the pressure switch connector.
  7. Refill the reservoir and bleed the system.
  1. Disconnect the battery negative cable.
  2. Drain the power steering fluid into a suitable container.
  3. Remove the power steering drive belt.
  4. Cover the A/C compressor or alternator, as applicable, with a shop towel, then disconnect the suction and pressure hoses from the power steering pump. Remove the gaskets.

    Click image to see an enlarged view
    Fig. Exploded view of the power steering pump and related components-1999 2.0L non-turbo engines


    Click image to see an enlarged view
    Fig. Power steering pump mounting-1999 2.0L turbo and 2.4L engines
  5. Detach the pressure switch connector. Unfasten the retaining bolts, then remove the pump assembly.
  6. If necessary, remove the retainers, then remove the pump bracket.
  7. Installation is the reverse of the removal procedure.
  8. For vehicles with A/C, when installing the power steering pump, install it to the bracket so that it faces toward the front of the vehicle. Then use the A/C pulley to adjust the belt tension.
  9. Refill the reservoir and bleed the system.
  1. Disconnect the battery negative cable.
  2. Drain the power steering fluid into a suitable container.
  3. Remove the power steering drive belt.
  4. Disconnect the supply and return lines.
  5. Remove the pump mounting bolts.
  6. Remove the power steering pump mounting bracket.
  7. Remove the power steering pump.
  8. Installation is the reverse order of removal.
    1. Tighten the power steering pump bracket bolt to 36 ft. lbs. (49 Nm).
    2. Tighten the power steering pump mounting bolts to 21 ft. lbs. (29 Nm).
  9. Bleed the power steering system.
  10. Check the tension of the power steering pump belt.


Click image to see an enlarged view
Fig. Exploded view of the power steering pump-Diamante
  1. Disconnect the battery negative cable.
  2. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
  3. Remove the power steering pump drive belt.
  4. Remove the pressure switch connector from the side of the pump.
  5. If the alternator is located under the oil pump, cover it with a shop towel to protect it from oil.
  6. Disconnect the high pressure hose and the return hose from the pump.
  7. Remove the pump drive belt and unbolt the pump from its bracket and remove the pump.
To install:
  1. Install the pump, wrap the belt around the pulley and tighten the bolts that secure the pump to 17 ft. lbs. (24 Nm).
  2. Replace the O-rings and connect the high pressure hose. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the mounting nut with lockwasher to 17 ft. lbs. (24 Nm).
  3. Using a new hose clamp, connect the return line.
  4. Attach the pressure switch connector.
  5. Adjust the belt tension and tighten the adjusting bolts.
  6. Refill the reservoir and bleed the system.


Click image to see an enlarged view
Fig. Exploded view of the power steering pump-Mirage
  1. Drain the power steering system as follows:
    1. Disconnect the return hose at the reservoir and place into a suitable container.
    2. Disable the ignition system. While cranking the engine, turn the wheels several times, until system has been drained.
  2. Disconnect the battery negative cable.
  3. Remove the pressure switch connector from the side of the pump.
  4. If the alternator is located under the oil pump, cover it with a shop towel to protect it from oil.
  5. Disconnect the pressure line.
  6. Remove the steering pump drive belt and the water pump pulley drive belt.
  7. Remove the water pump pulley.
  8. Remove the bolts that secure the oil pump, then remove the pump from its bracket.
To install:
  1. Install the power steering pump and tighten the mounting bolts to specifications.
  2. Install the water pump pulley and tighten the mounting bolts 14 ft. lbs. (19 Nm).
  3. Install and adjust the drive belts.
  4. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the nut that secures the pressure line to 13 ft. lbs. (18 Nm).
  5. Connect the return line.
  6. Attach the pressure switch connector.
  7. Refill the reservoir and bleed the system.

2.4L Engine





Click image to see an enlarged view
Fig. Exploded view of the power steering pump-1994-00 Galant with 2.4L engine
  1. Disconnect the battery negative cable.
  2. Loosen and remove the power steering pump drive belt.
  3. Remove the pressure switch connector from the side of the pump.

NOTE
If the alternator is located under the oil pump, cover it with a shop towel to protect it from oil.

  1. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
  2. Disconnect the pressure line.
  3. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  2. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  3. Connect the return line and secure with the clamp.
  4. Attach the pressure switch connector.
  5. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the system.


Click image to see an enlarged view
Fig. Exploded view of the power steering pump-1999-2003 Galant with 2.4L engine
  1. Disconnect the battery negative cable.
  2. Loosen and remove the power steering pump drive belt.
  3. Remove the pressure switch connector from the side of the pump.
    NOTE
    If the alternator is located under the oil pump, cover it with a shop towel to protect it from oil.
  4. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
  5. Disconnect the pressure line.
  6. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  2. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  3. Connect the return line and secure with the clamp.
  4. Attach the pressure switch connector.
  5. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the system.

3.0L Engine



  1. Disconnect the battery negative cable.
  2. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
  3. Remove the power steering pump drive belt.
  4. Remove the pressure switch connector from the side of the pump.
  5. If the alternator is located under the oil pump, cover it with a shop towel to protect it from oil.
  6. Disconnect the high pressure hose and the return hose from the pump.
  7. Remove the pump drive belt and unbolt the pump from its bracket and remove the pump.
To install:
  1. Install the pump, wrap the belt around the pulley and tighten the bolts that secure the pump to 17 ft. lbs. (24 Nm).
  2. Replace the O-rings and connect the high pressure hose. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the mounting nut with lockwasher to 17 ft. lbs. (24 Nm).
  3. Using a new hose clamp, connect the return line.
  4. Attach the pressure switch connector.
  5. Adjust the belt tension and tighten the adjusting bolts.
  6. Refill the reservoir and bleed the system.
  1. Disconnect the battery negative cable.
  2. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
  3. Remove the power steering pump drive belt.
  4. Remove the pressure switch connector from the side of the pump.
  5. If the alternator is located under the oil pump, cover it with a shop towel to protect it from oil.
  6. Disconnect the high pressure hose and the return hose from the pump.
  7. Remove the pump drive belt and unbolt the pump from its bracket and remove the pump.
To install:
  1. Install the pump, wrap the belt around the pulley and tighten the bolts that secure the pump to 17 ft. lbs. (24 Nm).
  2. Replace the O-rings and connect the high pressure hose. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the mounting nut with lock washer to 17 ft. lbs. (24 Nm).
  3. Using a new hose clamp, connect the return line.
  4. Attach the pressure switch connector.
  5. Adjust the belt tension and tighten the adjusting bolts.
  6. Refill the reservoir and bleed the system.

3.8L Engine



  1. Disconnect the negative battery cable.
  2. Remove the power steering drive belt.
  3. Disconnect the pressure switch connector electrical connector.
  4. Disconnect the supply and return hoses and gaskets.
  5. Disconnect the stabilizer links.
  6. Turn the steering wheel fully to the left.
  7. Remove the power steering pump mounting bolts.
  8. Remove the power steering pump.
  9. Installation is the reverse order of removal. Torque the power steering pump mounting bolts to 36 ft. lbs. (49 Nm).

Front





Click image to see an enlarged view
Fig. Exploded view of the power steering pump-Diamante
  1. Disconnect the battery negative cable.
  2. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
  3. Remove the power steering pump drive belt.
  4. Remove the pressure switch connector from the side of the pump.
  5. If the alternator is located under the oil pump, cover it with a shop towel to protect it from oil.
  6. Disconnect the high pressure hose and the return hose from the pump.
  7. Remove the pump drive belt and unbolt the pump from its bracket and remove the pump.
To install:
  1. Install the pump, wrap the belt around the pulley and tighten the bolts that secure the pump to 17 ft. lbs. (24 Nm).
  2. Replace the O-rings and connect the high pressure hose. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the mounting nut with lockwasher to 17 ft. lbs. (24 Nm).
  3. Using a new hose clamp, connect the return line.
  4. Attach the pressure switch connector.
  5. Adjust the belt tension and tighten the adjusting bolts.
  6. Refill the reservoir and bleed the system.

Rear



  1. Disconnect the negative battery cable.
  2. Drain the power steering fluid.
  3. Remove the rear power steering pump heat protector, located on the engine side of the differential on the transaxle.
  4. Disconnect the pressure line from the pump.
  5. Disconnect the suction hose from the pump.
  6. Remove the mounting bolts and remove the pump from the transaxle.
  7. The installation is the reverse of the removal procedure. Tighten the mounting bolts to 17 ft. lbs. (24 Nm).
  8. Refill the reservoir and bleed the system.

CAUTION
Extreme caution should be taken when testing the rear steering pump. Ensure that the vehicle is supported safely and that all components are torqued to specification prior be testing.

See below power steering related solved problems :----

Steering Wheel Locked?


How to replace Power Rack and Pinion Steering Gear on Acura Car Models?


How to replace Power Steering Pump on Acura Car Models?

Also bleeding:
                                    

How to replace Steering Linkage on Acura Car Models?


How to replace Steering Wheel on Acura Car Models?

How to replace Power Steering Pump on 1999 Acura TL?

How to Disarming the Air Bag System?

How to remove steering wheel on Chevrolet Malibu?

How to Remove Power steering Pressure Hose on Dodge Stratus

Car steering wheel makes noise?

Car makes clicking or tapping sound?

http://schematicsdiagram.blogspot.com/2011/12/car-makes-clicking-or-tapping-sound.html

@