@

max

Thursday

DODGE Diesel Engine Oil Pan Removal?

The Procedure to replace Oil pan for Dodge RAM Truck Diesel Engines.

The complete procedure for 2wd and 4wd models.
Also this procedure covers following Engine models
5.9L & 6.7L Diesel Engines.

The procedure starts here:---

2WD Models

  1. Open the hood.
  2. Remove the negative battery cables.
  3. Raise and support the vehicle.
  4. Remove the transmission oil cooler lines.
  5. Remove the propeller shaft.
  6. Remove the starter bolts.
  7. Support the starter.
  8. Remove the torque converter bolts.
  9. Remove the exhaust hanger bolts.
  10. Remove the gear shift cable.
  11. Remove the wiring harness.
  12. Remove the transmission mount.
  13. Remove the crossover bolts.
  14. Position the transmission jack.
  15. Remove the bell housing bolts.
  16. Remove the transmission.
  17. Remove the flywheel housing bolts (8).
  18. Remove the flex plate bolts (8).
  19. Remove the engine oil dip stick.
  20. Drain the oil.
  21. Remove the steering rack bolts.
  22. Remove the oil pan bolts.
  23. Remove the oil pickup bolts.
  24. Remove the oil pan.
To install:
  1. Clean the sealing surfaces of the cylinder block and oil pan with a suitable cleaner.
  2. Clean the oil pan.
  3. Clean the oil pan T-joints.
  4. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar®°silicone rubber adhesive sealant or equivalent.
  5. Position the new oil pan gasket.
  6. Place suction tube in oil pan and guide them into place. Using a new tube-to-block gasket, install and tighten the suction tube bolts by hand. Starting with the oil pump inlet bolts, tighten the bolts to 18 ft. lbs. (24 Nm). Tighten the remaining tube brace bolts to 32 ft. lbs. 43 Nm
  7. Starting in the center and working outward, tighten the oil pan bolts to 21 ft. lbs. (28 Nm).
  8. Install the steering rack bolts.
  9. Install the flex plate.
  10. Install the flywheel to crankshaft adapter. Tighten to 101 ft. lbs. (137 Nm).
  11. Install the transmission.
  12. Install the flywheel housing assembly with the starter motor attached and tighten bolts to 57 ft. lbs. (77 Nm).
    NOTE
    A new clamping ring must be used on early or late builds, automatic or manual. Do not reuse clamping ring.
  13. Install the EGR cooler.
  14. Install the fan and fan shroud
    NOTE
    Make sure that the fan shroud seal is properly seated in the radiator fan shroud and that it is not out of position causing excessive contact with the radiator coolant tubes.
  15. Remove the transmission jack.
  16. Install the crossmember bolts.
  17. Install the transmission mount.
  18. Install the wiring harness.
  19. Install the gear shift cable.
  20. Install the exhaust hanger bolts.
  21. Install the torque converter bolts.
  22. Install the starter.
  23. Install the starter bolts.
  24. Install the transmission oil cooler lines.
  25. Connect the negative battery cables.
  26. Close the hood
4WD Models

  1. Open the hood.
  2. Disconnect the battery negative cables.
  3. Remove the intake air assembly.
  4. Remove the radiator shroud retaining bolts.
  5. Install engine support fixture No. 8534B.
  6. Raise and support the vehicle.
  7. Drain the engine oil.
  8. Loosen the front engine mount bolts.
  9. Lower the vehicle.
  10. Use the engine support fixture No. 8534B to raise engine out of the front mounts.
  11. Remove the engine oil dipstick.
  12. Raise and support the vehicle.
  13. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
  14. Remove oil pan and suction tube.
  15. Remove the 2 bolts from the front of the engine block stiffener.
  16. Remove the oil pan.
    image

    Fig. Exploded view of the oil pan mounting-diesel engines
To install:
  1. Clean the sealing surfaces of the cylinder block and oil pan with a suitable cleaner.
  2. Clean the oil pan.
  3. Clean the oil pan T-joints.
  4. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone rubber adhesive sealant or equivalent.
  5. Position the new oil pan gasket.
  6. Place suction tube in oil pan and guide them into place. Using a new tube-to-block gasket, install and tighten the suction tube bolts by hand. Starting with the oil pump inlet bolts, tighten the bolts to 18 ft. lbs. (24 Nm). Tighten the remaining tube brace bolts to 32 ft. lbs. (43 Nm).
  7. Starting in the center and working outward, tighten the oil pan bolts to 21 ft. lbs. (28 Nm).
  8. Install the engine oil dipstick.
  9. Install the engine block stiffener.
  10. Install the flywheel to crankshaft adapter. Torque to 101 ft. lbs. (137 Nm).
  11. Lower the vehicle.
  12. Lower the engine into the motor mounts and tighten the through bolts to 64 ft. lbs. (88 Nm).
  13. Remove the engine support fixture No. 8534.
  14. Install battery negative cables.
  15. Fill the crankcase with new engine oil.
  16. Start engine and check for leaks. Stop engine, check oil level, and adjust, if necessary.
  17. Remove the engine support fixture No. 8534B.
  18. Install the fan and fan shroud.
    NOTE
    Make sure that the fan shroud seal is properly seated in the radiator fan shroud and that it is not out of position causing excessive contact with the radiator coolant tubes.
  19. Fill the engine oil.
  20. Connect the battery negative cables.
  21. Close the hood.


These details will help.
Thanks.           

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html


12 comments:

  1. Hi, Thanks for sharing nice post.I had been searching for many times about this.But this post stopped my searching.Thanks again.
    Dow Corning DC 705 silicone diffusion pump oil

    ReplyDelete
  2. Thanks for sharing the post with us. Get the proper rail parts suppliers from HI rail pickup wheels for sale who offers the high quality of railroad equipment.

    ReplyDelete
  3. It's a case of the fact that it is so imperative to have a decidedly ready mental guide of the split dodge varieties you intend to actualize. used car dealerships near me

    ReplyDelete
  4. Thanks for sharing such an amazing blog that helped me to understand the importance of repairing automobiles in-house. Hi Rail Truck Gear are a great way to get your work done.

    ReplyDelete
  5. During the Elizabethan occasions the act of hair removal, (not of leg, armpit or pubic hair), of their eyebrows and the hair from their temples to give the presence of a more drawn out temple and brow was in vogue. Tree Cutting Stockton

    ReplyDelete
  6. By getting two or three comparative quotes from different tree contractors, you can usually save money and hire the tree removal service that you feel the most comfortable with. Stump Removal Franklin

    ReplyDelete
  7. These were a portion of the reasons why you should recruit proficient tree administrations to eliminate trees securely and in right manner. Tree care procedures Huntington Beach

    ReplyDelete
  8. Machos Gracias for your blog post. Thanks Again. Really Great.Safe Stump Grinding Nashville

    ReplyDelete
  9. Frequently, we basically don't have the opportunity or the assets where to discard all the waste that the normal house gathers throughout the long term.removal companies north london

    ReplyDelete
  10. I wrote about a similar issue, I give you the link to my site. oven

    ReplyDelete

@